Most people love jewels designed in a particular manner and with various materials, but they never question how they are made. It is important to note that multiple processes are involved before the final product is gotten. The methods consist of the process of mixing the right materials and colors to come with specific designs. This discussion will focus on the procedures of making Tufa casting custom jewelry NM.
Stone preparation kicks of the process of creating various jewels. Not every stone can be used in this process but those that are of right size and fits the design of products you intend to produce. Stones should be of good quality. After finding the perfect stones use various tools to smoothen them until they are super smooth. Both sizes should appear super soft, flat and similar to each other.
After the stones have been prepared, it is time to make sketches of what one wants to produce. Sketching takes a lot of time because if errors are made, correcting them again can be costly and time consuming. Therefore, when the sketching process begins one needs to stay in a conducive environment completely.
The next process is carving the stone where the sketches have been made. There are multiple tools that experts advice carvers to use in this process. And those that are highly recommended include chisel tools, needles, and file used for wood carving. This process calls for perfection because one cannot afford to make a mistake because reversing them is never an option. Space that is created is used to pour melted silver.
Carbonizing of the stone happens at this point and comes before silver is poured. Pieces of stone can be attached using pieces of rubber or clamps. Silver contents are placed in a crucible and heated at a certain temperature to melt. When silver has reached its melting state, it is then poured into the intended place, and the results should be achieved within a short time.
The cast silver should be sand cleaned to smoothen the model. The good thing is that even after the cleaning process has been done, the texture on the model is still left there. Also, the cleaning process can be done in a citric acid pickling solution. This solution removes any fire scale that might have occurred during the soldering process.
At this point polishing is inevitable. The sole aim of polishing to have the products look attractive and appealing. The most common ways to shine the designs involved the use of water, rubber and other recommended polishing compounds. The different stages of polishing will use compounds that are either abrasive or non abrasive.
On completion of most processes, the products are almost ready for the market. Although they are available, there is room for designers to put various styles on them before they are sold. This can be done keeping mind your target market and what you intended to create. As much as other stages take a lot of time, sanding and polishing take the most time.
Stone preparation kicks of the process of creating various jewels. Not every stone can be used in this process but those that are of right size and fits the design of products you intend to produce. Stones should be of good quality. After finding the perfect stones use various tools to smoothen them until they are super smooth. Both sizes should appear super soft, flat and similar to each other.
After the stones have been prepared, it is time to make sketches of what one wants to produce. Sketching takes a lot of time because if errors are made, correcting them again can be costly and time consuming. Therefore, when the sketching process begins one needs to stay in a conducive environment completely.
The next process is carving the stone where the sketches have been made. There are multiple tools that experts advice carvers to use in this process. And those that are highly recommended include chisel tools, needles, and file used for wood carving. This process calls for perfection because one cannot afford to make a mistake because reversing them is never an option. Space that is created is used to pour melted silver.
Carbonizing of the stone happens at this point and comes before silver is poured. Pieces of stone can be attached using pieces of rubber or clamps. Silver contents are placed in a crucible and heated at a certain temperature to melt. When silver has reached its melting state, it is then poured into the intended place, and the results should be achieved within a short time.
The cast silver should be sand cleaned to smoothen the model. The good thing is that even after the cleaning process has been done, the texture on the model is still left there. Also, the cleaning process can be done in a citric acid pickling solution. This solution removes any fire scale that might have occurred during the soldering process.
At this point polishing is inevitable. The sole aim of polishing to have the products look attractive and appealing. The most common ways to shine the designs involved the use of water, rubber and other recommended polishing compounds. The different stages of polishing will use compounds that are either abrasive or non abrasive.
On completion of most processes, the products are almost ready for the market. Although they are available, there is room for designers to put various styles on them before they are sold. This can be done keeping mind your target market and what you intended to create. As much as other stages take a lot of time, sanding and polishing take the most time.
About the Author:
Get a summary of the things to keep in mind when choosing a tufa casting custom jewelry NM designer and more information about an experienced designer at http://www.bojoejewelry.com now.
No comments:
Post a Comment